end cap
英 [end kæp]
美 [end kæp]
网络 端盖; 管帽; 堵头; 端帽; 封端
双语例句
- Separate the end cap from the bumper.
将末端端盖和保险杆分隔开。 - The end of the recoil cavity is actively arranged with an end cap with a bullet outlet.
所述制退腔体的端部活动设置带子弹出口的端盖。 - Gatsby took up his drink. Separate the end cap from the bumper.
盖茨比端过一杯酒来。将末端端盖和保险杆分隔开。 - The split type end caps are integrally formed by end cap connecting bolts in connection.
所述端盖为剖分式，通过端盖连接螺栓连接为一体。 - Working Gas Study for End Cap Shower Counter of Beijing Spectrometer
北京谱仪端盖簇射计数器工作气体的研究 - The end cap will be used as the bearing or swivel point.
端盖将被用来作为轴承或旋转点。 - Pull back the wheelhouse liner and remove the bolts attaching the end cap to the front fender.
拉下舵手室外套，拆去连接末端端盖到前挡泥板的螺栓。 - Drawer bodies will have bottom and sides formed into one piece center section. Front and back panels are spot-welded to center section. Install the screw attaching the front of the end cap to the underside of the quarter panel.
抽屉底部和两边为单片设计。前、板面为点焊。安装连接末端端盖前侧到部分板底侧的螺丝。 - The Designing and Technology of High-frequency Inducing Brazing Equipment for End Cap of Electromagnetic Change Valve
电磁换向阀端盖高频感应钎焊设备研制及工艺探讨 - The "AP" Bearing also contains a spacer, seal, seal wear rings, axle end cap, cap screws, locking plate and backing ring.
AP轴承还集成了隔圈、密封、密封耐磨环、轴端盖、端盖螺钉、锁定板以及后挡环等部件。 - Install the bolts attaching the end cap to the front fender.
安装连接末端端盖到前挡泥板的螺栓。 - Install the screw attaching the front of the end cap to the underside of the quarter panel.
安装连接末端端盖前侧到部分板底侧的螺丝。 - After each time's well logging, open the upper bushing and the lower end cap.
每次测完井后，打开上护帽、下堵头。 - End Cap: Belt Tensioning System, easy access, easy adjustment.
完第：皮带张紧系统，方便，调整方便。 - Carefully check the amount of water seepage from the end cap and end bell weep hole.
仔细地检查漏水孔端盖与端座水的渗出量。 - A single-phase permanent magnetism brushless electric generator with compensation windings comprises a stator, a rotor and a front end cap.
一种具有补偿绕组的单相永磁无刷发电机，它由定子、转子和前端盖组成。 - Position the end cap on the rear of the retainer and the outer edge of the bumper.
在扣件尾部和保险杆边缘外部定位末端端盖。 - The end cap is provided with a connecting terminal which is fixed with the spring and the filter element.
端盖上设置有接线端子并在其上固定有弹簧与滤芯配合。 - The Monte-Carlo simulation of production and transmission of photons in the prototype of end cap time of flight counter
飞行时间计数器端盖模型中光产生和传输的蒙德卡罗模拟 - Carriage belt; Spindle Kit; Carriage assy trailing cable; Main logic board; Service station; power supply; Spindle end cap.
笔架皮带；笔架；数据线；主板；服务站；电源板；纸卡；纸杆；进纸组件；托架； - Pull the flag to the top of the pole. Separate the end cap from the bumper.
把旗升到旗杆顶端。将末端端盖和保险杆分隔开。 - Two numerical examples including the side wall thermal driving case and the end cap mechanical driving case were also given.
最后，给出侧壁热驱动和端盖机械驱动的两个算例。 - Prototype of end cap shower counter and its beam test
BES端盖簇射计数器模型的束流测试 - The flow field of viscous gas in a closed rotating cylinder with end cap and side wall drives is investigated by asymptotic analysis.
本文用渐近分析方法研究了封闭旋转圆筒内粘性气体的流动，提出了一种简单的解析计算方法。整个流场分为六个区，给出了各区问题的提法。 - From about 30~ 301 m, all cores were oriented by cement end cap method.
从钻孔深度30～301m，利用水泥端帽法对岩芯进行了定向。 - The Simulation and Manufacture of The End Cap Pressure Sensor
端盖压头仿真与研制 - A6 relativistic magnetron resonant system is calculated and simulated by equivalent circuit and high frequency structure simulator ( HFSS of agilent), and the effect of end cap to resonant frequency is especially presented in this paper.
利用等效电路法和高频分析软件（HFSS）对A6相对论磁控管谐振系统进行了理论计算与模拟分析，着重考虑了相对论磁控管端帽的引入对谐振频率的影响。 - The outer side of the non-round center wheel is meshed with the planet gears, and the planet wheels and the inner curve ring gear mesh. It has the front and rear end cap which is sealed space inside.
非圆中心轮外侧是与其啮合的行星齿轮，而行星轮又与内曲线齿圈啮合，前后是端盖，其间是密封空间。 - As for structure, a new cylinder supported bearing structure has been proposed, and a new kind of fixed valve plate which is fixed on the end cap of pump has been developed.
结构上，提出了新的缸内支撑轴承式结构，设计了一种固定安装于后端盖的固定式配流盘。 - A method combining oil-filled housing heat dissipation and end cap heat dissipation was chosen to assure steady work of the junction box system. 2.
采用腔体内部充油散热和端盖散热相结合的方法，保证了接驳盒系统的稳定运行。